Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
We've come across the article on How to Install a Bathtub Yourself listed below on the net and thought it made sense to write about it with you on this page.
Installing a tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably hard job. If the old bathtub is conveniently obtainable, the task can relocate speedily; if you have to open a wall to remove the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a house handyman's skills, although you will need a helper to vacate the old bathtub and set in the new one. Ensure you have qualified yourself for the task as well as fit trying it. As opposed to employing a specialist to take control of a halfway-completed project, it is better to think about utilizing one before you start. Opportunities are you might need a professional plumber to make tube connections.
This post will help you set up a brand-new bathtub in your shower room if you have actually already purchased a brand-new bathtub and also don't require to change the plan of your previous water system pipelines.
Your tools as well as product checklist must consist of the following:
Preparing for the Setup
To start with, the supporting structure supplied with the bathroom needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets system to stop stress on the bath tub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing taps can be fairly problematic as a result of the restricted accessibility that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, position the bathtub in the needed placement. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bathtub until the level reviews degree.
To install taps, fit all-time low of the outermost adaptable tap port to the proper supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints and also brand-new pipework for leaks and tighten them if required. Fill up the bath tub as well as additionally check the overflow outlet and the typical outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bathtub ought to wait up until the tub has been utilized a minimum of when as this will certainly resolve it right into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the maker given backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The former type should be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing problems with dampness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and installations. They are offered in tubes and cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was introduced to that report on How to Install a Bathtub Yourself from an associate on our other web address. Sharing is nice. Helping people is fun. Thank you for your time. Kindly check our blog back soon.
Need Help? Hire Us Now! Report this page